Analysis of horizontal tank with jacket based on ANSYS Workbench

Authors

JIA Mingxia, Advanced Manufacturing Technology Center, Shandong University of Science and Technology, Qingdao, Shandong 266590, China
ZHONG Peisi, Advanced Manufacturing Technology Center, Shandong University of Science and Technology, Qingdao, Shandong 266590, China
YANG Mei, Advanced Manufacturing Technology Center, Shandong University of Science and Technology, Qingdao, Shandong 266590, China
ZHANG Xiaodong, Advanced Manufacturing Technology Center, Shandong University of Science and Technology, Qingdao, Shandong 266590, China
LIN Weiwei, Advanced Manufacturing Technology Center, Shandong University of Science and Technology, Qingdao, Shandong 266590, China
LV Xiaodong, Advanced Manufacturing Technology Center, Shandong University of Science and Technology, Qingdao, Shandong 266590, China

Abstract

Targeting at the horizontal tank with jacket from a certain project as the research subject, applying the finite element software ANSYS Workbench, the structural static analysis showed that under the full load and the snow condition the deformation and stress were similar and the reinforced rib had significantly effect on the tank. Meantime, the response spectrum analysis told that under the seismic condition the maximum stress occurred in the saddle, which was lower than the allowable stresses of the materials. The reliabilities of the tank were validated, and optimization method was presented.

Publication Date

2-28-2016

First Page

63

Last Page

66

DOI

10.13652/j.issn.1003-5788.2016.02.016

Recommended Citation

Mingxia, JIA; Peisi, ZHONG; Mei, YANG; Xiaodong, ZHANG; Weiwei, LIN; and Xiaodong, LV (2016) "Analysis of horizontal tank with jacket based on ANSYS Workbench," Food and Machinery: Vol. 32: Iss. 2, Article 16.
DOI: 10.13652/j.issn.1003-5788.2016.02.016
Available at: https://www.ifoodmm.cn/journal/vol32/iss2/16

References

[1] 麦源, 白勇. 食品加工设备中外压容器的稳定性数值分析[J]. 食品与机械, 2014, 30(1): 137-140.
[2] 邱放. 基于ANSYS的压力容器爆炸事故原因及避免措施分析[J]. 食品与机械, 2009, 25(5): 93-95.
[3] 陈延. 外压容器设计有关问题探讨[J]. 压力容器, 2007(1): 60-62.
[4] 刘梦飞, 郑甲红, 高警. 采摘机—核桃树系统的仿真与试验[J]. 食品与机械, 2014, 30(1): 107-110.
[5] 中华人民共和国国家发展和改革委员会. NB/T 47003.1—2009 钢制焊接常压容器[S]. 北京: 新华出版社, 2010: 10-11.
[6] 向寓华. 化工容器与设备[M]. 北京: 高等教育出版社, 2009: 264.
[7] 中华人民共和国国家发展和改革委员会. JB/T 4731—2005 钢制卧式容器[S]. 北京: 新华出版社, 2005: 44-45.
[8] 中华人民共和国建设部. GB 50011—2001 建筑抗震设计规范[S]. 2008年版. 北京: 中国建筑工业出版社, 2008: 27-30.
[9] 陈芳, 宋樱, 刘玉华. 天津市温室结构性能检测方案[J]. 农业工程, 2013, 3(S1): 55.