Abstract
Objective By analyzing the working conditions of the conveyor, the factors affecting the transportation were studied and the mechanical characteristics model of the conveyor was determined. Methods Analytical mechanics method was used to obtain the mechanical characteristics model affecting the equal-pitch variable pitch factor. The three-dimensional model was built using Unigraphics NX and imported into Ansys workbench software. The static simulation, modal analysis and optimization design were performed. Results Through simulation analysis and optimization, the maximum deformation of the cream conveyor occurred at the top edge of the screw shaft, and the mass, total deformation and equivalent stress of the optimized structure were reduced by more than 10%. Conclusion This method could provide a theoretical reference for mechanical research and structural design of conveyors.
Publication Date
7-28-2018
First Page
78
Last Page
82
DOI
10.13652/j.issn.1003-5788.2018.07.016
Recommended Citation
Jian, YANG; Xinwen, LI; and Weibing, LIU
(2018)
"Characteristic analysis and optimization design of extrusion cream conveyor,"
Food and Machinery: Vol. 34:
Iss.
7, Article 16.
DOI: 10.13652/j.issn.1003-5788.2018.07.016
Available at:
https://www.ifoodmm.cn/journal/vol34/iss7/16
References
[1] 王顺俊. 特殊绞龙制造工艺探讨［J］. 焊接质量控制与管理, 2014, 12(3): 63-65.
[2] 杨世平, 杨湘军, 胡自化, 等. 绞龙类零件数控加工宏程序的开发［J］. 组合机床与自动化加工技术, 2003(4): 40-41.
[3] 肖培军, 朱云, 万辉, 等. 蒸脱机进料封闭绞龙结构的改进与应用［J］. 粮食与食品工业, 2013, 20(3): 33-37.
[4] 宋亚英. 变螺距螺旋结构参数的理论研究［J］. 苏州大学学报: 自然科学版, 1996, 12(4): 96-100.
[5] HURNEY A P, CROFT B J, GRACE D, et al. Influence of harvester base cutters on ratooning of sugarcane[M]. [S.l.]: BSES Limited Publication, 2005: 47-48.
[6] ROBERTS A W. The influence of granular vortex motion on the volumetric performance of enclosed screw conveyors[J]. Powder Technology, 1999, 104(1): 56-67.
[7] OWEN P J, CLEARY P W. Prediction of screw conveyor performance using the discrete element method (DEM)[J]. Powder Technology, 2009, 193(3): 274-288.
[8] DAI Jian-jun, JOHN R G. Biomass screw feeding with tapered and extended sections［J］. Powder Technology, 2008, 186: 56-64.
[9] DAI Jian-jun, JOHN R G. A model for biomass screw feeding［J］. Powder Technology, 2008, 186: 40-55.
[10] 俞天兰, 彭德其, 俞天翔, 等. 自转清洗包塑钢丝螺旋的流体动力学优化设计研究［J］. 力学与实践, 2012, 34(2): 54-57.
[11] 王东霞. 螺旋输送机的数值分析及优化设计的研究［D］. 郑州: 河南工业大学, 2012: 43-45.
[12] 赵匀. 机构数值分析与综合［M］. 北京: 机械工业出版社, 2005: 34-35.
[13] 邱志平, 王晓军, 许孟辉, 等. 工程结构不确定优化设计技术［M］. 北京: 科学出版社, 2013: 51-52.
[14] 王乐勤, 陈涛, 吴大转, 等. 卧螺离心机螺旋输送器结构强度的参数化分析［J］. 机械设计, 2010, 27(5): 67-70.
[15] 傅彩明, 毛文贵. 离心机螺旋输送器有限元仿真分析［J］. 机械设计与制造, 2008(4): 77-79.