Abstract
In order to solve the problem of water pollution and cigarette wrinkle at the cigarette guide plate device of YJ19 Cigarette Maker, the structure of the cigarette guide plate device was improved by combining the arc groove with the air suction hole. The cigarette transferring mode was changed from closed type to open type, and then the results were validated. The experiment results showed that the unclean defect rate of cigarette lap was reduced from 1.45% to 0, and the wrinkle defect rate of cigarette decreased from 1.16% to 0.30%. The quality of cigarettes has been improved.
Publication Date
4-28-2021
First Page
124
Last Page
128
DOI
10.13652/j.issn.1003-5788.2021.04.023
Recommended Citation
Shu-qing, WU; Yong, SUN; Fang, YANG; and Xue-yan, HUANG
(2021)
"Improvement on cigarette guide plate device of YJ19 cigarette maker,"
Food and Machinery: Vol. 37:
Iss.
4, Article 23.
DOI: 10.13652/j.issn.1003-5788.2021.04.023
Available at:
https://www.ifoodmm.cn/journal/vol37/iss4/23
References
[1] 许昌烟草机械有限责任公司. YJ19B卷烟机机器说明书[Z]. 许昌: 许昌烟草机械有限责任公司, 2016: 5-20.
[2] 中国国家标准化管理委员, 中华人民共和国国家标准. 卷烟第三部分: 包装、卷制技术要求及贮运: GB 5606.3—2005[S]. 北京: 中国标准出版社, 2005: 21-28.
[3] 刘舒畅, 张峻松, 翟义龙, 等. 浅谈烟支表面黄斑缺陷的产生原因及预防管控[J]. 轻工科技, 2015(9): 109.
[4] 杨蓝, 周沅桢, 刘泽, 等. 烟支黄斑污染物的追溯与鉴别[J]. 贵州农业科学, 2019, 47(5): 132-137.
[5] 杜赫, 李晓波, 马俊, 等. 基于ATR-FTIR技术的黄斑烟污染源鉴别[J]. 食品与机械, 2019, 35(11): 85-88.
[6] 蔡雨铮, 闫绍峰, 赵彬, 等. 蒸汽冷凝传热特性的研究[J]. 化工管理, 2017(21): 190.
[7] 王猛. 卷烟机产生烟支表面各类问题的研究与处理方法[J]. 中国科技博览, 2018(20): 2-5.
[8] 赵梅生, 陈锐, 伍先, 等. 消除黄斑烟质量隐患的研究[J]. 价值工程, 2013, 32(18): 174.
[9] 舒奎武, 李宪成, 于帅, 等. 卷烟机产生烟支表面水渍、黄斑问题分析与处理[J]. 轻工科技, 2015, 31(12): 69-70.
[10] 张卫宾, 简金领. PASSIM接装机水松纸夹末及冷凝水分析与改进[J]. 设备管理与维修, 2015(1): 64-66.
[11] 彭永刚, 刘德凯, 曲飚, 等. Φ 5.25 mm烟支皱纹的形成及解决办法[J]. 设备管理与维修, 2014(7): 29-31.
[12] 王志魁, 向阳, 王宇. 化工原理[M]. 北京: 化学工业出版社, 2018: 289-292.
[13] 梅自强. 纺织辞典[S]. 北京: 中国纺织出版社, 2007: 147-155.
[14] 何立明, 赵罡, 程邦勤. 气体动力学[M]. 北京: 国防工业出版社, 2009: 174-180.